Pcb Version Usb 3 Ueye Le

PCB Version USB 3 UEye LE

PCB Version USB 3 UEye LE The optical center of the usb 3 ueye le pcb version is exactly the center of the board. note that the holes for mounting the lens holder are not symmetrical to the optical center. they are moved in one direction (see drawing above). fig. 413: usb 3 ueye le with lens holder front view fig. 414: usb 3 ueye le with lens holder side view. The i/o connector of the usb 3 ueye le can be equipped with a 2 x 4 pin connecting plug with a 1.27 mm (50 mil) lead spacing. ids imaging development systems gmbh shall not be liable for any damage to the camera or connected devices arising from installation of the connecting plug.

PCB Version USB 3 UEye LE

PCB Version USB 3 UEye LE The digital output of the usb 3 ueye le is not potential free and has no protective circuits. it is recommended to use the flash as low active. Usb 3/usb 3.1 ueye cameras are limited usable under usb 2.0. depending on the camera model, not all camera functions are available in usb 2.0 mode. usb 3/usb 3.1 ueye cameras are optimized for usb 3.0 ports and are not tested by ids imaging development systems gmbh under usb 2.0. The ueye le usb 3.1 gen 1 camera models are also available in the af (active focus) variant. the mechanical data for each camera model can be found on our website directly at the respective camera model beneath in the "downloads" tab. Therefore, first unplug the usb and/or i/o cable from the camera. dimensions of the housing version fig. 405: usb 3 ueye le back view fig. 406: usb 3 ueye le front view fig. 407: usb 3 ueye le bottom view fig. 408: usb 3 ueye le top view fig. 409: usb 3 ueye le side view © 2024 ids imaging development systems gmbh.

PCB Version USB 3 UEye LE

PCB Version USB 3 UEye LE The ueye le usb 3.1 gen 1 camera models are also available in the af (active focus) variant. the mechanical data for each camera model can be found on our website directly at the respective camera model beneath in the "downloads" tab. Therefore, first unplug the usb and/or i/o cable from the camera. dimensions of the housing version fig. 405: usb 3 ueye le back view fig. 406: usb 3 ueye le front view fig. 407: usb 3 ueye le bottom view fig. 408: usb 3 ueye le top view fig. 409: usb 3 ueye le side view © 2024 ids imaging development systems gmbh. You can operate your ueye le usb 3.1 rev. 1.2 camera using the software development kit ids peak. ids peak contains all libraries and software tools required for operating and programming. Using the example of the ui 388xle, the specifications for maximum temperatures, mounting, shield and esd protection are provided. the listed data is applicable for all ueye le usb 3.1 gen 1 board level versions. the ueye le usb 3.1 gen 1 camera can only be assembled from back to front. Pcb version usb 3 ueye le attention: make sure to avoid mechanical or electrical damage of the printed circuit board or its connections. do not touch the printed circuit board while it is powered. always hold the board by the edges to avoid the risk of electrostatic discharge damage. This section of the manual contains information on connecting the cameras and wiring ios. for information on a camera's power consumption, please refer to the camera and sensor data section. this section contains information on all camera models sorted by sensor type. notice!.

PCB Version USB 3 UEye LE

PCB Version USB 3 UEye LE You can operate your ueye le usb 3.1 rev. 1.2 camera using the software development kit ids peak. ids peak contains all libraries and software tools required for operating and programming. Using the example of the ui 388xle, the specifications for maximum temperatures, mounting, shield and esd protection are provided. the listed data is applicable for all ueye le usb 3.1 gen 1 board level versions. the ueye le usb 3.1 gen 1 camera can only be assembled from back to front. Pcb version usb 3 ueye le attention: make sure to avoid mechanical or electrical damage of the printed circuit board or its connections. do not touch the printed circuit board while it is powered. always hold the board by the edges to avoid the risk of electrostatic discharge damage. This section of the manual contains information on connecting the cameras and wiring ios. for information on a camera's power consumption, please refer to the camera and sensor data section. this section contains information on all camera models sorted by sensor type. notice!.

PCB Version USB 3 UEye LE

PCB Version USB 3 UEye LE Pcb version usb 3 ueye le attention: make sure to avoid mechanical or electrical damage of the printed circuit board or its connections. do not touch the printed circuit board while it is powered. always hold the board by the edges to avoid the risk of electrostatic discharge damage. This section of the manual contains information on connecting the cameras and wiring ios. for information on a camera's power consumption, please refer to the camera and sensor data section. this section contains information on all camera models sorted by sensor type. notice!.

PCB Version USB 3 UEye LE

PCB Version USB 3 UEye LE

PCB of the day! HUSB238 is a smart USB PD chip 🔌💡🔋